 |
GILMER
WOOD COMPANY |
||||
| $100
minimum order |
|||||
|
Unique
and |
______________________________________________ Tools ______________________________________________ Hitachi
Bandsaw Blades Hitachi #939-971, designed for the CB75F and the older B600A, blade size 0.65 x 75 x 2812 mm (approx. .026 x 2.95 x 110.7”) $170.00 Hitachi
#939-973, designed for the CB100F and the older B1000, blade size 0.8
x 102 x 4450 mm (approx. .032 x 4.01 x 175.2”) $395.00 ______________________________________________ Dotco Air Drill Used but well-maintained. Works fine. 6200 r.p.m. with a Jacobs chuck. Sorry, no key. #W14350
_____________________________________________ Tannewitz
click on photo for close-ups and back and side views Serial # 73038 Motor
is a dual voltage 240/480 volt 3 phase-currently wired 480 volt ______________________________________________ Buss 30” planer click on photo for back and side views Model 44, 20 hp to the cutterhead, 5 hp to the feed works, 220 volt, 3 phase, three knife cutterhead, separate motor for raising & lowering the table, s/n5008. It sounds like it could use new cutterhead shaft bearings. $2500.00 ______________________________________________ Pin Router click on photo for back view 5 hp, 220 volt, 3 phase, ½” collet, 33 x 33” table. This machine has been modified to an air-operated raising & lowering of the spindle, controlled by a foot switch. $1500.00 ______________________________________________ Cincinnati #2M
Horizontal Mill, 220/440 volt, 3 phase, s/n E672W. ______________________________________________ Powermatic #60 8” Jointer, 220 volt, single phase, three knife cutterhead, s/n 7861052. 1285.00 ______________________________________________
______________________________________________ Greenlee
#493 Table Saw click on photo for close-up and alternate view This is a tilting-table saw with a ball-bearing, direct drive, 5 hp 220 volt 3 phase motor with a magnetic starter. 1 ¼” arbor. The mechanism that tilts the table is damaged. We used this machine as a rip saw with a power feed mounted on a corner of the table so we never used the tilt feature. Back in the 1980s we used this machine to re-saw thousands of feet of Hawaiin Koa cants and used a 20” diameter blade. Nothing ever stalled this machine. Comes as shown without a blade, miter gauge, or fence. Weighs approximately 1400 lbs. Sold as is-$400.00. ______________________________________________ Destaco Pull-action Latch Clamps Model # 351. The pull bar is adjustable. 8 ½” overall length with a 4” drawing movement. Do not come with latch plates. Used but in good condition. # C8247 $5.00 each ______________________________________________ BAND SAW POWER FEED This
is a new/surplus machine that was recently purchased but never used
and is still in the crate. This is a duplicate of a machine that has
been used in our workshop (photo) for over twenty years and in that
time has given trouble-free service. Manufactured in Taiwan it was designed
to mount on band saws 32” and larger, although we quite easily
adapted it for use on a 24” band saw. It has 10 forward and reverse
speeds and comes with a 12” high roller bearing fence. The motor
is 220volt, 3 phase (can be run on single phase power with a solid-state
converter). Anyone doing any amount of serious re-sawing will soon find
this an indispensable tool. Crated it weighs approximately 400 lbs.
_____________________________________________ Tool
Boxes Tool
10-16-03T1664 ______________________________________________ Tool
10-16-03T1666 ______________________________________________
______________________________________________ MACHINERY contact Myles Gilmer, Jim MacDermot, or Marc Culbertson. (503) 274-1271 Fax (503) 274-9839 click here to e-mail inquiry or order 800# 1-888-667-3979
|
||||||||||||||||||
